收藏本站
SOT23-5 Voltage Regulator Evaluation Board User’s Guide
2.3
GETTING STARTED
The SOT23-5 Voltage Regulator Evaluation Board is fully assembled and tested. All
that is required for operating is a user supplied voltage regulator and a supply voltage
source. Some of the tests that may be completed using the SOT23-5 Voltage Regulator
Evaluation Board shall now be described.
2.3.1
Ground Current and Quiescent Current
When measuring ground current, jumper JP3 should be removed, otherwise leave
jumper JP3 on. To measure ground current, perform the following steps:
1. Add desired load resistor to R5.
2. Remove jumpers JP3 and JP4.
3. Connect an ammeter across testpoints TP6(+) and TP7(-). Select the
appropriate meter scale for the evaluated device.
4. Connect a voltmeter across testpoints TP9(+) and TP10(-).
5. Add jumper JP1.
6. Add jumper JP2 to pins 1 and 2.
7. Apply source voltage to testpoints TP1(+) and TP2(-).
8. Verify the voltage across testpoints TP9 and TP10 is within the expected range
of the device being tested.
9. Read the Ground Current directly from the ammeter connected to testpoints TP6
and TP7.
10. Vary the input voltage to obtain data for ground current versus input voltage.
With no load attached to the output of the voltage regulator, the measured ground
current is also called the quiescent current of the regulator.
11. Add the load selection jumper, JP4.
12. Read the Ground Current directly from the ampere meter connected to testpoints
TP6 and TP7.
13. The data collected will be the ground current versus load current.
2.3.2
Adjustable Output Voltage (ADJ)
The output voltage of some adjustable voltage regulators may be adjusted by selecting
appropriate resistor divider values connected to the Adjust (ADJ) pin. R2 and R3 pads
are available to be used as the voltage divider.
2.3.3
Shutdown input selection (SHDN)
The Shutdown (SHDN) input selection may be set to V IN , GND, or a user supplied
voltage using testpoint TP5. To select V IN as the SHDN voltage, place a jumper across
pins JP2-1 and JP2-2. To select GND as the SHDN voltage, place a jumper across pins
JP-2 and JP-3. To select a user specified input such as a function generator, remove
the jumper from JP2 and connect the external voltage source positive lead (+) to
testpoint TP5 and the negative lead (-) to testpoint TP4.
DS51811A-page 10
? 2009 Microchip Technology Inc.
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
SP5004EGP SUPERPRO 5004EGP PROGRAMMER
SP7121EK-L IC LED DRVR BACKLIGHT SOT23-6
SP7600EN2-L IC LED DRVR PWM STP-DWN 8HNSOIC
SPB2 PANEL SWING KIT
SPIKECUBE SURGE SUPPRESSR 1OUT DIRECT PLUG
SPIKESTIK SURGE SUPPRESSOR SPIKE STIK 6OUT
SPS-615-HG SURGE SUPP 6OUT 15'CORD HOSP GRD
SR202 SHELF FIXED 4-POST HEAVY DUTY
相关代理商/技术参数
SOT23-5PIN 制造商:IRF 制造商全称:International Rectifier 功能描述:Package Dimensions
SOT-23-6 制造商:RICOH 制造商全称:RICOH electronics devices division 功能描述:SOT-23-6 (SC-74)
SOT23-6 制造商:ZETEX 制造商全称:ZETEX 功能描述:Thermal Resistance and Derating Information
SOT23-6L 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:LOW VOLTAGE 4ohm SPDT SWITCH
SOT23-8L 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:DUAL BILATERAL SWITCH
SOT23-DIP_DS2 制造商:Distributed By MCM 功能描述:SOT23 TO DIP ADAPTER ADAPTER 制造商:MCM 功能描述:SOT23 TO DIP ADAPTER ADAPTER
SOT23ESD-A 制造商:未知厂家 制造商全称:未知厂家 功能描述:Surface Mount Transient Voltage Suppressors
SOT23F 制造商:ZETEX 制造商全称:ZETEX 功能描述:Surface mounted, 3 pin package